153Korea(주)소형모터백화점

CUSTOMER CENTER

02-2613-6124

02-6949-6125

FAX : 02-2613-6151
E-mail :153korea@153korea.co.kr

NTGM102ZJ1

1. NTGM102ZJ1
	NTGM102ZJ1
	NTGM102ZJ1

3. DIMENSIONS

NTGM102ZJ1 DIMENSIONS

4. MEASUREMENT OF FLOW QUANTITY

NTGM102ZJ1 Measurement of flow quantity

1)The inclination of the pump is within 5^o
2)Water is used to measure after having been left more than 30min in 20±5^oC
3)The pump starts at DC12V, and the measurement starts within 5sec after the pump turning on the water from the exit side, the flowing quantity of 30sec is measured, and the value is converted into the fiowing quantity of 1min

5. MEASUREMENT OF SUNCTION HEIGHT

NTGM102ZJ1 Measurement of Sunction height

1)The inclination of the pump is within 5^o
2)Water is used to measure after having been left more than 30min in 20±5^oC
3)The pump starts at DC12V, and the measurement starts within 5sec. the water sucking up from the surface of the water is measured. (with fully dried inside the pump)

6. MEASUREMENT OF PUMPING UP HEIGHT

NTGM102ZJ1 Measurement of Pumping up height

1)The inclination of the pump is within 5^o
2)Water is used to measure after having been left more than 30min in 20±5^oC
3)The pump starts at DC12V, and pumps up the water. then upper height of the water is measured.

7. MEASUREMENT OF NOISE

NTGM102ZJ1 Measurement of noise

1)The inclination of the pump is within 5^o
2)Water is used to measure after having been left more than 30min in 20±5^oC
3)The pump starts at DC12V, and microphone placed 150mm fromt the pump with the water fills in the hose to measure.
4)No crease on the bending part of the hose.

8. SPECIFICATIONS

ITEM	PERFROMANCE	NOTE
Voltage for use	DC 9~13V	The voltage of the operation check is DC 12V
Flow quantity	1.31±0.25/min	Refer to the Fig.1.
Sucking up height	140mm or more	Measured with fully dried pump. Refer to the Fig.2 for the installation position of the pump unit.
Pump up height	500mm or more	Refer to the Fig.3 for the installation position of the pump unit.
Noise	65dB or less	Measured at 150mm from the pump by the motor positive rotation. Refer to the Fig.4. (Range A)

9. PERFROMANCE

ITEM	PERFROMANCE		NOISE
Motor current input	No load	150mA or less
	Rated load	250mA or less
	Restriction	700mA or less
Motor case surface temperature	80^oC or less		Measured with the rated voltage and rated load after stability of termperature
Surface temperature rise of motor case	50K or less		Measured the surface of the motor after the pump gear being locked and energized for 2min.
Motor insulation resistance	1MΩ or more(Motor)		Between the live part and not live metal part :DC 100V
Motor dielectric strength	AC 100V 1min (Motor)		Between the live part and not live metal part Cut off current:5mA
Motor Insulation class	Class A
Wire pull strength	The wires are not come off or broken after loaded 19.6N to the lead wires in A,B,C,D AND E directions for 10sec.		Wire pull directions

10. SPECIFICATIONS

ITEM	TEST CONDITION
High temperature test	After left to an atmosphere with ambient temperature of 60±2^oC for 168h and replaced in the normal temperature and humidity for 1h.
Low temperature test	After left to an atmosphere with ambient temperature of -30±2^oC for 168h and replaced in the normal temperature and humidity for 1h.
Humidity test	After left to an atmosphere with ambient temperature of 40±2^oC and 95±5% for 168h and replaced in the normal temperature and humidity for 1h.
Heat cycle test	1 cycle is -30±2^oC for 2h, 60±2^oC for 2h and then replaces in the normal temperature and humidity for 1h.
Drop test	Withstands the shock of the drop with acceleration of 490m/s² for 1 time in each direction of X, and Z.
Vibration test	Withstands the viberation of 3mm double amplitude 8 to 35 Hz (sweep time is 1min) for 20min in each direction X,Y and Z.

※ 관련있는 제품들
40-2545 CS-0115 CS-0580 CS-0590 CS-0720 CS-0730 GGMN SERIES 온수보일러용 외 DP1 GP4 GGP2K 385 DAP-6402DSEA-1 NTGM102ZJ1 NTGM102ZH1